background image

 

76-QD0460EN-01Y00-00 

Engage the tip tool (like socket, bit and so on) securely to the fastener before pulling the throttle lever.

  

Pull the throttle lever of the tool slowly to start. Sudden start may cause accident or malfunction.

  

Working in unusual positions is dangerous. Hold the tool securely and carry out working in stable  

  posture, preparing for accidental movement at the same time. 

Be careful about burn injury. During use and immediately right after tightening, metal parts, tip tool, bolts 

and nuts may be hot.

  

Do not touch metal parts, tip tool, bolts and nuts  immediately right after tightening.

 

Also, do not touch the exhaust port of the tool during use. There is a fear of burn injury.   

Do not make the foreign object such as metal pieces, invaded to the product. There is fear of fire.

 

Do not stick the pin, bar and so on into the inlet or exhaust of the cooling fan nor plug the hole.

 

Do not remove the parts from the tool. If you use such tool as the mounted parts or screws removed,   

it may result in accident.

 

Do not pinch the power supply cord of the battery  charger in the object to be tightened or do not  

contact the cord with rotating parts. Otherwise, it may be damaged and result in accident.

 

Use the exclusive battery pack and battery charger only.

 

Do not disassemble or modify the battery pack and battery  charger.

 

Doing so may result in heat generation, fire, electric shock, or injury.  

Do not throw the battery pack into fire or heat it.

 

Doing so may result in rupture or release of hazardous substances.   

Do not drive a nail or give an impact such as fall on the battery pack or battery charger.

 

Doing so may result in heat generation, fire, electric shock, and/or injury.

 

Do not short-circuit the terminals of the battery pack.   

Do not carry or store the battery pack with metal object such as nail. Doing so may result in   

smoking, ignition, or rupture. 

 

If  the  battery  pack  gets  hot  during  its  use,  stop  using  it  immediately  and   after  detaching  the  battery 

pack from the tool, contact our distributor or sales representative where you have purchased.

 

If  the  battery  pack  leaks,  stop  using  it  and  contact  our   distributor  or  sales  representative  where  you 

have purchased.

 

If the electrolyte of the battery gets in your eyes, do not  pass your hand over your eyes, but flush them 

with a plenty of clean water and seek medical attention. Failure to do so may result in loss of vision.

  

If the electrolyte of the battery comes in contact with body part or clothes, rinse with a plenty of cle an         

 

water and seek medical attention. Failure to do so may result in dermal inflammation or injury.

 

Noise might be regulated under laws and regulations of the country or regions where the product is used.

 

The tool must be used at noise levels below those prescribed by them, not to trouble the 

surroundings. Install sound insulation walls, depending on the necessity. 

If noise levels at the operator’s position exceed 85dB (A), be sure to use earplugs.

 

Even if noise levels are not more than 85dB (A), it is  recommended to use earplugs. 

When the tool receives damage such as breakage or if you feel uneasiness during the use, stop using 

the tool immediately and after removing the battery pack, ask repair or inspection to YOKOTA or  

Summary of Contents for YZ-TH600



































Reviews: