background image

 

YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc 

・【

Noise  might  be  regulated  under  laws  and  regulations  of  the  country  or  regions  where  the  product  is 

used.

】 

The tool must be used at noise levels below those prescribed by them. Install sound insulation walls, 

depending on the necessity. 

If noise levels at the operator’s position exceed 85dB (A), be sure to use earplugs. Even if noise levels 

are not more than 85dB (A), it is recommended to use earplugs.

 

Do not install this product in a place likely to be exposed to water, direct sunlight, much dust, heat, oil, or 

moving parts of industrial equipment. Otherwise, it may cause fire, electric shock, or accident. 

 

1.2.  Electrical Safety 

  Warning

 

This product is for the indoor exclusive use.    Do not use it in rain, in a damp place and a wet place. 

Moreover, never use it in the place with the fear of the ignition and the explosion, because those are 

hazardous situation.

 

Do not hold the power supply cord for battery charger for carrying or pull the cord to unplug it. In addition, 

be careful to avoid stepping on or being caught by the cord, and/or damage by excessive force. Damage 

of the power supply cord may result in accident. 

Do not insert the power supply cord of the battery charger between the objects to be tightened or contact 

it with rotating parts. Otherwise, it may be damaged and cause accident.   

  Use the exclusive battery pack and battery charger only.   

Failure to do so may result in rupture of it and damage of the product or property. 

Use the battery charger at rated supply voltage (AC 100-240 V).   

Do not use DC power supply, engine generator, or power transformer. Failure to do so may result in heat 

generation and fire. 

Do not disassemble or modify the battery pack and battery charger.   

Doing so may result in heat generation, fire, electric shock, or injury. 

Do not throw the battery pack into fire or heat it.   

Doing so may result in rupture or release of hazardous substances.   

Do not drive a nail or give an impact such as fall on the battery pack or battery charger.   

Doing so may result in heat generation, fire, electric shock, and/or injury. 

Do not short-circuit the terminals of the battery pack.   

Do not carry or store the battery pack with metal object such as nail. Doing so may result in smoking, 

ignition, or rupture. 

If the battery pack gets hot during its use, stop using it immediately and contact your sales outlet or sales 

agent.   

If the battery pack leaks, stop using it and contact your sales outlet or sales agent.   

Be sure to fully insert the power plug of the battery charger.   

Failure to do so may result in electric shock or fire due to heat generation. 

Summary of Contents for YS-e600
























Reviews: