background image

 

YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc 

16 

5.6.  Press the pairing button of the tool. 

Press the button with the flat face of TF pin 2 x 90 until it beeps and the LED of the tool blinks fast 

in yellow. 

 

 

 

 

 

 

*Do not continue to press the pairing button after the buzzer beep and fast blinking of the 

LED. 

*After the battery pack is installed and the throttle lever is pulled, make sure that the LED 

blinks in blue or yellow. Then press the pairing button. 

Regarding  the  blinking  of  the  LED,  if  the  pairing  is  done,  it  blinks  in  blue  (only  one 

blinking). If the pairing is not done, it blinks in yellow (repeated blinking). 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.7.  When the LED of the tool lights in red and goes off, the pairing is completed. 

The wireless unit transmits the set value and the tool is ready to operate.   

The LED of selected TOOL number on the wireless unit lights in green. 

*1: If the LED lights in purple, pairing is failed. Carry out the steps as described in 5.6. 

*2: Even if the battery pack is removed and inserted again, the pairing status is maintained.

 

OK to push

Throttle

Buzzer

Blue LED

(Pairing completed)

Pairing Button

Yellow LED

(Pairing not completed)

Buzzer beeping & LED fast blinking

Do

 

not

 

push.

Do

 

not

 

push.

Figure 1

 

Pressing-down timing of pairing button (After attaching the battery pack.)

Summary of Contents for YS-e600
























Reviews: