manualshive.com logo in svg

YOKOGAWA AQ6370D, User Manual

Share
Download
YOKOGAWA AQ6370D User Manual Download Page 346

9-21

IM AQ6370D-01EN

Other Operations

1 

2 

3 

4 

5 

6 

7 

8 

9 

10 

11 

App

Index

Turning Automatic Offset ON/OFF

You can specify whether to have the instrument perform automatic offset adjustment on 
its internal amplifier circuit.

1.

 Press 

SYSTEM

. 

2.

  Press the 

MORE

 soft key repeatedly until the MORE 2/4 menu is displayed.

3.

  Press the 

AUTO OFFSET OFF ON

 soft key. The settings turns ON and OFF 

each time you press the key. When this is set to ON, the offset is adjusted 
automatically.

Note

•  If the AUTO OFFSET is OFF, the offset can fluctuate over time, and the level axis 

performance can degrade.  Always have it turned ON. 

•  When the AUTO OFFSET is set to ON, 

 is displayed at the bottom of the screen. 

Setting the Remote Monitor

This function can be used to monitor the instrument’s screen and control the instrument 
from a remote PC that is connected over TCP/IP. To use this function, you need remote 
monitoring software (not included).

1.

 Press 

SYSTEM.

2.

  Press the 

MORE

 soft key repeatedly until the MORE 2/4 menu is displayed.

3.

  Press the 

NETWORK SETTING

 soft key. The Ethernet setup menu is displayed.

4.

  Press the 

REMOTE MONITOR

 soft key. The remote monitor setup menu is 

displayed.

5.

  Press the 

MONITOR PORT

 soft key. Each time you press the soft key, the setting 

toggles between ON and OFF. When this is set to ON, the remote monitor is 
enabled.

Sharing Directories

The user area directory of the AQ6370D internal memory can be shared on a PC.

1.

 Press 

SYSTEM

.

2.

  Press the 

MORE

 soft key repeatedly until the MORE 2/4 menu is displayed.

3.

  Press the 

NETWORK SETTING

 soft key. The Ethernet setup menu appears.

4.

  Press the 

FOLDER SHARING

 soft key. A directory sharing setup menu appears.

5.

  Press the 

READ ONLY

 soft key. Directory sharing is enabled.

Pressing the 

DISABLE

 soft key disables directory sharing.

Configuring a Firewall

You can close the TCP port when the communication interface (ETHERNET), remote 
monitoring, and directory sharing are not in use.

1.

 Press 

SYSTEM

.

2.

  Press the 

MORE

 soft key repeatedly until the MORE 2/4 menu is displayed.

3.

  Press the 

NETWORK SETTING

 soft key.

 The Ethernet setup menu appears.

4.

  Press the 

FIREWALL

 soft key.

 Each time you press the soft key, the setting toggles between ON and OFF.
 When this is set to ON, the firewall is enabled.

9.6  Other Settings

Summary of Contents for AQ6370D






























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands