Home
/
YOKOGAWA
/
AQ6370D
/
User Manual

YOKOGAWA AQ6370D, User Manual

Share

Page: 157 / 445

YOKOGAWA AQ6370D User Manual Download Page 157

6-37

IM AQ6370D-01EN

W

aveform Display

1

2

3

4

5

6

7

8

9

10

11

App

Index

Finding the Level Peak/Bottom to the Left of the Advanced Marker

5.

When the advanced marker is displayed at the peak or bottom of the waveform,

press the

NEXT SEARCH LEFT

soft key. The advanced marker is set to the next

peak (local maximum value) or bottom (local minimum value) on the left.

Turning Off the Advanced Marker Display

Press the

OFF

soft key.

Note

The advanced marker display automatically turns off if you perform any of the following
operations.
•  Execute auto measurement (section 5.1)
•  Clear all traces (section 6.11)
•  Change the vertical axis settings (section 5.2) and execute a measurement (section 5.13)
•  Change the number of samples (section 5.8) and execute a measurement (section 5.13)

Clearing All Advanced Markers

1.

Press

MARKER

. A soft key menu for marker settings appears.

2.

Press the

ADVANCE MARKER

soft key.

A soft key menu for advanced marker settings appears.

3.

Press the

ALL CLEAR

soft key. All displayed advanced markers (moving

markers, power density markers, and integrated power markers) are cleared.

6.9 Marker Display

«
...
155
156
157
158
159
...
»

Summary of Contents for AQ6370D






























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands