manualshive.com logo in svg

YOKOGAWA AQ6370D, User Manual

Share
Download
YOKOGAWA AQ6370D User Manual Download Page 243

7-68

IM AQ6370D-01EN

When the Logging Item Is DFB-LD

4.

  To display the graph of DFB-LD analysis items, press the soft keys below.

•  To display the peak wavelength graph: 

PEAK WL

•  To display the peak level graph: 

PEAK LEVEL

•  To display the side mode suppression ratio graph: 

SMSR

•  To display the signal-to-noise ratio graph: 

OSNR

•  To display the center wavelength graph: 

CENTER WL

•  To display the spectral width graph of the center wavelength based on the -XdB 

WIDTH (Center WL/SPWD) parameter: 

SPEC WD

•  To display the total power graph: 

MORE1/2

 and then 

POWER

 

 

   

•  To display the mode offset graph: 

MORE1/2

 and then 

OFFSET

•  To display the spectral width (σ) graph of the center wavelength based on the 

RMS parameter: 

MORE1/2

 and then 

SIGMA

•  To display the spectral width (Kσ) graph of the center wavelength based on the 

RMS parameter: 

MORE1/2

 and then 

K SIGMA

 

 

   

7.15  Analysis Data Logging

Summary of Contents for AQ6370D






























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands