Yealink Yealink SIP-T46G Administrator'S Manual Download Page 50

Page: 50 / 625

Administrator’s Guide for SIP-T2_Series_T4_Series IP Phones

Procedure

Network parameters can be configured manually using the configuration files or locally.

Configuration File

<MAC>.cfg

Configure network parameters of
the IP phone manually.

Parameters:

network.internet_port.type

network.ip_address_mode

network.internet_port.ip

network.internet_port.mask

network.internet_port.gateway

network.primary_dns

network.secondary_dns

Local

Web User Interface

Configure network parameters of
the IP phone manually.

Navigate to:

http://<phoneIPAddress>/servlet
?p=network&q=load

Phone User Interface

Configure network parameters of
the IP phone manually.

Details of Configuration Parameters:

Parameters

Permitted Values

Default

network.internet_port.type

0, 1 or 2

Description:

Configures the Internet (WAN) port type for IPv4 when the IP address mode is
configured as IPv4 or IPv4 & IPv6.

0-DHCP

1-PPPoE (not applicable to SIP-T42G/T41P IP phones)

2-Static IP Address

Note: If you change this parameter, the IP phone will reboot to make the change take
effect.

Web User Interface:

Network->Basic->IPv4 Config

Phone User Interface:

Menu->Settings->Advanced Settings (default password: admin) ->Network->WAN
Port->IPv4

Summary of Contents for Yealink SIP-T46G


















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Yealink SIP-T46G

Reviews:

Related manuals for Yealink SIP-T46G

Brands by name

Popular brands

Yealink Yealink SIP-T46G, Administrator'S Manual

Search results

Summary of Contents for Yealink SIP-T46G

Reviews:

Related manuals for Yealink SIP-T46G

Brands by name

Popular brands