Yealink VC120 Administrator'S Manual Download Page 73

Page: 73 / 319

Configuring Network

IPv6 Network parameters need to be configured manually on the system are described below.

Parameter

Description

Configuration Method

Mode (IPv4/IPv6)

Configures the IP address mode.

Default:

IPv4

Note:

If you change this parameter,

the IP phone will reboot to make the
change take effect.

Remote Control

Web User Interface

Static IP

Enables or disables the system to
use manually configured IPv6
network settings.

Default:

Disabled

Note

: If you change this parameter,

the system will reboot to make the
change take effect.

Remote Control

Web User Interface

IP Address

Configures the IPv6 address
assigned to the system.

Default:

Blank

Note

: If you change this parameter,

the system will reboot to make the
change take effect.

Remote Control

Web User Interface

IPv6

prefix((0~128)

Configures the IPv6 prefix.

Default:

Blank

Note

: If you change this parameter,

the system will reboot to make the
change take effect.

Remote Control

Web User Interface

Gateway

Configures the IPv6 default gateway.

Default:

Blank

Note

: If you change this parameter,

the system will reboot to make the
change take effect.

Remote Control

Web User Interface

Static DNS/Static

IPv6 DNS

Triggers the static IPv6 DNS feature
to on or off.

Default:

Off

Note

: If you change this parameter,

the system will reboot to make the
change take effect.

Remote Control

Web User Interface

DNS Primary

Server/Primary

Configures the primary IPv6 DNS
server.

Remote Control

Web User Interface

Summary of Contents for VC120
































































































































































































































































































































Search results

Summary of Contents for VC120

Reviews:

Related manuals for VC120

Brands by name

Popular brands

Yealink VC120, Administrator'S Manual

Search results

Summary of Contents for VC120

Reviews:

Related manuals for VC120

Brands by name

Popular brands