manualshive.com logo in svg

YASKAWA GPD 506/P5, Troubleshooting Manual, Page: 8 / 67

Share
Download
YASKAWA GPD 506/P5 Troubleshooting Manual Download Page 8

PP.P5G5.03.Troubleshoot

Page 8

Rev. 06/11/2003

Motor overload, designed to protect the motor.
Fully adjustable from parameter setting (n033 and 

n034 for 506/P5 and E1-02 and E2-01 for 515/G5)

A pre-alarm can be selected as a minor fault by using 
the multi-function outputs.

OL1

Motor Overloaded

o

l1

Inverter overload, designed to protect the inverter.
120 or150% of inverter rated current for 1 minute.

515 -

150% for 1 minute

505 and 506 -

120% or 150% depending on drive 

capacity and setting parameter n116

OL2

Inv Overloaded

o

l2

Possible Cause(s): 

Motor is overloaded.

Corrective Action: 

Verify the program settings, reduce the load on the motor.

Possible Cause(s): 

Motor is overloaded.

Corrective Action: 

Verify the program settings, reduce the load on the motor.

505

Fault Codes

Major Fault 

- Motor coasts to a stop, the fault is displayed on the digital  

operator, and the fault relay is activated. 

506 

√

515 

√

Summary of Contents for GPD 506/P5




































































Reviews:

No comments