manualshive.com logo in svg

YASKAWA GPD 506/P5, Troubleshooting Manual, Page: 12 / 67

Share
Download
YASKAWA GPD 506/P5 Troubleshooting Manual Download Page 12

PP.P5G5.03.Troubleshoot

Page 12

Rev. 06/11/2003

The braking transistor has failed.

230V Units

- 0.4kW ~ 7.5kW

460V Units

- 0.4kW ~ 15kW

RR

DynBrk Transistr

The braking resistor temperature has exceeded the 

allowable value.
(Protects Yaskawa 3% duty cycle resistors only)

Can be selected as a minor fault by using the multi-
function outputs.

RH

DynBrk Resistor

Possible Cause(s): 

Shorted braking transistor, high DC bus voltage, defective braking 

resistor.

Corrective Action: 

Replace defective transistor or resistor, monitor DC bus level.

Possible Cause(s): 

Overhauling load, extended braking duty cycle, defective braking

resistor.

Corrective Action: 

Verify braking duty cycle, monitor DC bus voltage, replace resistor.

505

N/A

N/A

Fault Codes

Major Fault 

- Motor coasts to a stop, the fault is displayed on the digital  

operator, and the fault relay is activated. 

506 

√

515 

√

Summary of Contents for GPD 506/P5




































































Reviews:

No comments