manualshive.com logo in svg

YASKAWA GPD 506/P5, Troubleshooting Manual, Page: 10 / 67

Share
Download
YASKAWA GPD 506/P5 Troubleshooting Manual Download Page 10

PP.P5G5.03.Troubleshoot

Page 10

Rev. 06/11/2003

Inverter input power supply has an open phase.
Large imbalance of input voltage.

PF

Input Pha Loss

sp

1

Inverter output has an open phase.

LF

Output Pha Loss

sp

o

Possible Cause(s): 

Open phase on the input of the inverter. Loose terminal screws at 

terminals L1, L2, or L3. Program parameters set incorrectly (n083 for 506/P5, L8-05 for 515/G5)

Corrective Action: 

Tighten the terminal screws, check the input voltage, verify the program 

settings.

Possible Cause(s): 

Open phase on the output of the inverter. Loose terminal screws at 

terminals T1, T2, or T3. Program parameters set incorrectly. 

Corrective Action: 

Tighten the terminal screws, check the output voltage, verify the 

program settings.

Fault Codes

Major Fault 

- Motor coasts to a stop, the fault is displayed on the digital  

operator, and the fault relay is activated. 

505

506 

√

515 

√

506 

515 

√

505

Summary of Contents for GPD 506/P5




































































Reviews:

No comments