manualshive.com logo in svg

YASKAWA GPD 506/P5, Troubleshooting Manual, Page: 38 / 67

Share
Download
YASKAWA GPD 506/P5 Troubleshooting Manual Download Page 38

PP.P5G5.03.Troubleshoot

Page 38

Rev. 06/11/2003

Fault Codes

Parameter Setting Error 

- Inverter can’t run. The fault is displayed 

on the digital operator, and the fault relay is not activated.

OPE11

FC/ On-Dly

Carrier frequency data setting fault.

Upper limit (C6-01) >5KHz, and the lower limit      
(C6-02) <= 5KHz.

Carrier frequency proportional gain (C6-03) > 6 and 
(C6-01) < (C6-02).

N/A

Possible Cause(s): 

Parameter setting incorrect.

Corrective Action: 

Check the program settings and correct the errors.

Possible Cause(s): 

Connection not made properly, user software not configured to the 

proper baud rate or configuration. 

Corrective Action: 

Check all connections, verify all user side software configurations.

CALL

Serial Com Call

Serial communication transmission error. 
Communication has not yet been established.

call

505

506 

515 

√

505

506 

√

    

515 

√

Summary of Contents for GPD 506/P5




































































Reviews:

No comments