manualshive.com logo in svg

YASKAWA GPD 506/P5, Troubleshooting Manual, Page: 13 / 67

Share
Download
YASKAWA GPD 506/P5 Troubleshooting Manual Download Page 13

PP.P5G5.03.Troubleshoot

Page 13

Rev. 06/11/2003

The actual torque during deceleration has reached 

the regen torque limit for more than 3 seconds. 

(Open Loop Flux Vector mode only)

CF

Out of Control

N/A

In the zero servo mode, the motor shaft has       

rotated 10,000 non-quadrature PG pulses from the 

home position.

SVE

Zero Servo Fault

N/A

Possible Cause(s): 

The regen torque limit value is set too low, load torque is excessively 

large.

Corrective Action: 

Verify the program setting, L7-03 forward regen torque limit and L7-04 

reverse regen torque limit, extend the deceleration time. 

Possible Cause(s): 

Torque limit or zero servo gain set too low, load torque excessively 

large, PG signal noise.

Corrective Action: 

Verify the program parameters B9-01 zero servo gain and torque limit 

settings L7-01 ~ L7-02, check for noise on the PG signals.

505

Fault Codes

Major Fault 

- Motor coasts to a stop, the fault is displayed on the digital  

operator, and the fault relay is activated. 

506

515 

√

Summary of Contents for GPD 506/P5




































































Reviews:

No comments