manualshive.com logo in svg

YASKAWA GPD 506/P5, Troubleshooting Manual, Page: 5 / 67

Share
Download
YASKAWA GPD 506/P5 Troubleshooting Manual Download Page 5

PP.P5G5.03.Troubleshoot

Page 5

Rev. 06/11/2003

The pre-charge contactor opened while the inverter is 

running.

UV3

MC Answerback

U

u

3

Overvoltage of the main circuit when running.

230V Units 

- trip point 400V DC or more.

460V Units 

- trip point 800V DC or more.

600V Units

- trip point 1050V DC or more.

OV

DC Bus Overvolt

ou

„

This fault only applies to 230V units 18kW ~ 75kW , 460V units 22kW ~ 160kW and 

600V units 30kW ~ 160kW .

Possible Cause(s): 

Contacts on contactor are dirty, contactor does not function mechanically.

Corrective Action: 

Check the contactor, check the ribbon cable from the control board to the 

gate drive board.

Possible Cause(s): 

High input voltage at L1, L2, and L3. The deceleration time is set too 

short. Power factor correction capacitors are being used on the input to the inverter.

Corrective Action: 

Check the input circuit, verify the program parameters, add a braking 

resistor, remove the power factor correction capacitors.

505

Fault Codes

Major Fault 

- Motor coasts to a stop, the fault is displayed on the digital  

operator, and the fault relay is activated. 

506 

√

515 

√

Summary of Contents for GPD 506/P5




































































Reviews:

No comments