manualshive.com logo in svg

YASKAWA GPD 506/P5, Troubleshooting Manual, Page: 28 / 67

Share
Download
YASKAWA GPD 506/P5 Troubleshooting Manual Download Page 28

PP.P5G5.03.Troubleshoot

Page 28

Rev. 06/11/2003

o

l3

Over torque detection function.

A customer programmable current detection. Response 
may be selected. A minor fault contact output can be 
programmed by using the multi-function outputs. 

OL3

Overtorque Det 1

OL4

Overtorque Det 2

N/A 

Over torque detection function (2).

A customer programmable current detection. Response 
may be selected. A minor fault contact output can be 
programmed by using the multi-function outputs. 

Possible Cause(s): 

Motor is overloaded.

Corrective Action: 

Verify the program settings, reduce the load on the motor.

Possible Cause(s): 

Motor is overloaded.

Corrective Action: 

Verify the program settings, reduce the load on the motor.

Fault Codes                    

Minor Fault 

- Operation continues and the digital operator indication blinks 

The fault relay does not activate.

505

506 

√

   

515 

√

505

506 

515 

√

Summary of Contents for GPD 506/P5




































































Reviews:

No comments