27
YASKAWA AC Drive
CR700
Catalog
｜
KAEP C
710617
24
｜
YASKAWA
Bit
Torque screwdriver
Torque wrench
Bit socket holder
Terminal Type
Terminal
Signal Function (default)
Description (Signal Level)
Fault Relay
Output
MA
N.O. output (Fault)
・
Relay output
・
30 Vdc or less, 10 mA to 1 A
・
250 Vac or less, 10 mA to 1 A
・
Minimum load:
5 Vdc
，
10 mA (Values only for reference)
MB
N.C. output (Fault)
MC
Digital output common
Multi-Function
Digital Output
M
1
Multi-function digital output
(Brake Release Command)
・
Relay output
・
30 Vdc or less, 10 mA to 1 A
・
250 Vac or less, 10 mA to 1 A
・
Minimum load:
5 Vdc, 10 mA (Values only for reference)
Note: Switching life is estimated at
8,000,000 times (assumes 30 mA, inductive load)
and
200,000 times (assumes 1 A, resistive load). When an inductive load such as
relay coils is switched on and off, connecting the surge absorber parallel to the
load is an effective means to protect the contacts.
M
2
M
3
Multi-function digital output (During run)
M
4
M
5
Multi-function digital output (Speed agree
1)
M
6
Multi-Function
Photocoupler
Output
P
1
Multi-Function Photocoupler Output
(Drive Ready (READY))
・
Photocoupler output
・
48 Vdc or less, 2 to 50 mA
Note: Connect a fl ywheel diode
as shown below when
driving a reactive load
such as a relay coil. Diode
must be rated higher
than the circuit voltage.
C
1
P
2
Multi-Function Photocoupler Output
(Alarms)
C
2
Monitor
Output
FM
analog monitor (
1) (Output frequency)
Voltage output
・
0 to 10 Vdc for 0 to 100%
・
−
10 to 10 Vdc for
−
100 to 100%
Note: H
4-07 (Terminal FM Signal Level Select.) and H4-08 (Terminal AM Signal Level
Select.) to select the signal type for terminals AM and FM.
AM
analog monitor (
2) (Output current)
AC
Monitor common
0 V
Control Circuit Input Terminals (
200 V/400 V) (continued)
(50 mA max.)
Coil
External
power
48 V max.
Flywheel diode
Tools for Wiring European Style Terminal Blocks (Recommended product)
Screw size Screw type
Recommended Product
M
4
Slot
Prepare the following two tools.
･
Bit
【
PHOENIX CONTACT
】
Model: SF-BIT-SL
1,0X4,0-70
･
Torque screwdriver
【
PHOENIX CONTACT
】
Model: TSD-M
3NM (1.2 to 3 N
·
m)
M
5
Slot
When wiring drive models CR
70
2047 and CR70
4075 or earlier
models, be sure to correctly select tools based on the wire gauges.
Wiring Gauge:
≤
25 mm
2
or AWG
10
・
Bit
【
PHOENIX CONTACT
】
Model: SF-BIT-SL
1,2X6,5-70
･
Torque screwdriver
【
PHOENIX CONTACT
】
Model: TSD-M
3NM (1.2 to 3 N
·
m)
Wiring Gauge: ≥
30 mm
2
or AWG
8
･
Torque wrench that includes a torque measurement range of
4.5 N
·
m
･
Bit socket holder of
6.35 mm
M
6
Hex socket
(WAF: 5)
Prepare the following three tools.
･
Bit
【
PHOENIX CONTACT
】
Model: SF-BIT-HEX
5-50
･
Torque wrench that includes a torque measurement range of
9 N
·
m
･
Bit socket holder of
6.35 mm
Minus
Prepare the following three tools for the models CR
70
2088 to
2115, and CR70
4091.
･
Bit
【
PHOENIX CONTACT
】
Model: SF-BIT-SL
1,2X6,5-70
･
Torque wrench that includes a torque measurement range of
3.5 N
·
m
･
Bit socket holder of
6.35 mm
M
8
Hex socket
(WAF: 6)
Prepare the following three tools.
･
Bit
【
PHOENIX CONTACT
】
Model: SF-BIT-HEX
6-50
･
Torque wrench that includes a torque measurement range of
12 N
·
m
･
Bit socket holder of
6.35 mm
M
10
Hex socket
(WAF: 8)
Prepare the following three tools.
･
Bit
【
PHOENIX CONTACT
】
Model: SF-BIT-HEX
8-50
･
Torque wrench that includes a torque measurement range of
14 N
·
m
･
Bit socket holder of
6.35 mm
S
sq
D
Check the
“
Terminal size / Wire gauge
”
on the next page and prepare the tools for wiring.
Classifi cation
Terminal
Signal Function
Description
（
Signal Level
）
MEMOBUS /
Modbus
communications
D
+
Communications input (
+
)
MEMOBUS/Modbus communications:
Use a RS-
485 cable to connect the drive.
Note: Set DIP switch S
2 to ON to enable the
termination resistor in the last drive in
a MEMOBUS/Modbus network.
・
RS-
485
・
MEMOBUS/Modbus communications
protocol
115.2 kbps (max.)
D
−
Communications input (
−
)
AC
Shield ground
0 V
Serial Communication Terminals (
200 V/400 V Class)
Type
Terminal
Terminal Name (Default)
Function
External power
supply
input terminals
PS
External
24 V power
supply input
Supplies backup power to the drive control circuit, keypad, and option card.
21.6 Vdc to 26.4 Vdc, 700 mA
AC
External
24 V power supply ground
0 V
External Power Supply Input Terminals (
200 V/400 V Class)
Bit socket holder
S:
6.35 mm
Application screw slot
Featur
es
Catalog Code /
Selecting the Capacity
Basic
Instructions
Standar
d
Specifi
cations
Standar
d
Connection Diagram
Terminal
Specifi
cations
Dimensions
Fully
-Enclosed
Design
Peripheral Devices
and Options
Application
Notes
Gl
o
b
a
l S
e
rv
ic
e
Ne
tw
o
rk
Terminal
Specifi
cations
