Yamaha YFM400FAR Service Manual Download Page 89

Page: 89 / 481

3 - 28

CHK

ADJ

CLEANING THE AIR FILTER

5.Clean:

●

Air filter element

*****************************************************

Cleaning steps:

●

Wash the element gently, but thoroughly in
solvent.

WARNING

Use a cleaning solvent which is designed
to clean parts only. Never use gasoline or
low flash point solvents as they may cause
a fire or explosion.

●

Squeeze the excess solvent out of the
element and let it dry.

CAUTION:

Do not twist or wring out the element. This
could damage the foam material.

●

Apply engine oil to the element.

●

Squeeze out the excess oil.

NOTE:

The element should be wet but not dripping.

*****************************************************

6.Install:

●

Air filter element assembly

●

Air filter case cover

NOTE:

To prevent air leaks make sure that the sealing
surface of the element matches the sealing
surface of the case.

●

Seat
Refer to “SEAT, CARRIERS, FENDERS
AND FUEL TANK”.

Summary of Contents for YFM400FAR


































































































































































































































































































































































































































































































Search results

Summary of Contents for YFM400FAR

Reviews:

Related manuals for YFM400FAR

Brands by name

Popular brands

Yamaha YFM400FAR, Service Manual

Search results

Summary of Contents for YFM400FAR

Reviews:

Related manuals for YFM400FAR

Brands by name

Popular brands