Yamaha YFM400FAR Service Manual Download Page 318

Page: 318 / 481

9 - 11

–

ELEC

IGNITION SYSTEM

CORRECT

Spark plug gap:

0.6 ~ 0.7 mm (0.024 ~ 0.028 in)

INCORRECT

Repair or replace the spark plug.

OUT OF
SPECIFICATION
OR NO SPARK

4.Ignition spark gap

●

Disconnect the spark plug cap from the
spark plug.

●

Connect the dynamic spark tester

shown.

Spark plug cap

Spark plug

●

Turn the main switch to “ON”.

●

Check the ignition spark gap.

●

Crank the engine by pushing the starter
switch, and increase the spark gap until a
misfiring occurs.

Minimum spark gap:

6.0 mm (0.24 in)

MEETS SPECIFICATION

The ignition system is not faulty.

5.Spark plug cap resistance

●

Remove the spark plug cap.

●

Connect the pocket tester (

Ω

1k) to the

spark plug cap.

MEETS
SPECIFICATION

●

Check that the spark plug cap has the
specified resistance.

Spark plug cap resistance:

10 k

Ω

at 20 °C (68 °F)

OUT OF SPECIFICATION

Replace the spark plug cap.

Summary of Contents for YFM400FAR


































































































































































































































































































































































































































































































Search results

Summary of Contents for YFM400FAR

Reviews:

Brands by name

Popular brands

Yamaha YFM400FAR, Service Manual

Search results

Summary of Contents for YFM400FAR

Reviews:

Brands by name

Popular brands