Yamaha YFM400FAR Service Manual Download Page 324

Page: 324 / 481

9 - 17

–

ELEC

ELECTRIC STARTING SYSTEM

C0NTINUITY

TURNS

3.Starter motor

●

Connect the battery positive terminal

and starter motor cable

using a jumper

lead

●

Check the operation of the starter motor.

WARNING

●

A wire that is used as a jumper lead must
have the equivalent capacity or more as
that of the battery lead, otherwise the
jumper lead may burn.

●

This check is likely to produce sparks, so
be sure that no flammable gas or fluid is
in the vicinity.

DOES NOT TURN

Repair or replace the starter motor.

4.Starter relay

●

Remove the starter relay from the wire
harness.

●

Connect the pocket tester (

Ω

1) and the

battery (12 V) to the starter relay terminals.

CONTINUITY

Battery (+) terminal

→

Blue/White terminal

Battery (–) terminal

→

Blue/Black terminal

Tester (+) lead

→

Red terminal

Tester (–) lead

→

Black terminal

●

Check the starter relay for continuity.

NO CONTINUITY

Replace the starter relay.

Summary of Contents for YFM400FAR


































































































































































































































































































































































































































































































Search results

Summary of Contents for YFM400FAR

Reviews:

Brands by name

Popular brands

Yamaha YFM400FAR, Service Manual

Search results

Summary of Contents for YFM400FAR

Reviews:

Brands by name

Popular brands