manualshive.com logo in svg

Yamaha YFM400FAR, Service Manual

Share
Download
Yamaha YFM400FAR Service Manual Download Page 108

3 - 47

CHK

ADJ

CHECKING THE STEERING SYSTEM 

1.Place the machine on a level surface.
2.Check:

●

Steering assembly bushings
Move the handlebar up and down, and/or
back and forth.
Excessive play 

→

 Replace the steering stem

bearing.

3.Check:

●

Tie-rod ends
Turn the handlebar to the left and/or right
until it stops completely, then move the
handlebar from the left to the right slightly.
Tie-rod end has any vertical play 

→

 Replace

the tie-rod end.

4.Raise the front end of the machine so that

there is no weight on the front wheels.

5.Check:

●

Ball joints and/or wheel bearings
Move the wheels laterally back and forth.
Excessive free play 

→

 Replace the front

arms (upper and lower) and/or wheel
bearings.

ADJUSTING THE TOE-IN

1.Place the machine on a level surface.
2.Measure:

●

Toe-in
Out of specification 

→

 Adjust.

*****************************************************

Measurement steps:

NOTE:

Before measuring the toe-in, make sure that
the tire pressure is correct.

●

Mark both front tire tread centers.

●

Face the handlebar straight ahead.

Toe-in:

0 ~ 10 mm (0 ~ 0.39 in)
(with tires touching the ground)

CHECKING THE STEERING SYSTEM/

ADJUSTING THE TOE-IN

Summary of Contents for YFM400FAR


































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands