manualshive.com logo in svg

Yamaha YFM400FAR, Service Manual

Share
Download
Yamaha YFM400FAR Service Manual Download Page 192

4 - 69

ENG

CRANKSHAFT AND OIL PUMP

INSTALLING THE CRANKSHAFT AND 
BALANCER 

1.Install:

●

Crankshaft

NOTE:

Hold the connecting rod at the Top Dead
Center (T.D.C.) with one hand while turning
the nut of the installing tool with the other.
Operate the installing tool until the crankshaft
bottoms against the bearing.

CAUTION:

Apply engine oil to each bearing to protect
the crankshaft against scratches and to
make installation easier.

Crankshaft installer set 

12

:

P/N. YU-90050

Buffer boss installer set 

23

:

P/N. 90890-04088

Crankshaft installer bolt 

1

:

P/N. 90890-01275

Adapter #11 

3

:

P/N. YM-33279

Spacer (crankshaft):

P/N. YM-90070-A, 90890-04060

2.Install:

●

Crankshaft seal

NOTE:

Install the crankshaft seals in the correct place
and in the correct direction.

3.Install:

●

Balancer 

1

 

NOTE:

Align the punch marks 

a

 on the drive and

driven gears.

Summary of Contents for YFM400FAR


































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands