Yamaha YFM400FAR Service Manual Download Page 476

Page: 476 / 481

– 102 –

–

ELEC

COOLING SYSTEM

C0NTINUITY

CONTINUITY

6.Fan motor relay

●

Remove the fan motor relay from the wire
harness.

●

Connect the pocket tester (

Ω

1) and the

battery (12 V) to the fan motor relay
terminals.

Tester (+) lead

→

Red/Black terminal

Tester (–) lead

→

Blue terminal

Battery (+) terminal

→

Red/White terminal

Battery (–) terminal

→

White/Yellow terminal

●

Check the fan motor relay for continuity.

NO CONTINUITY

Replace the fan motor relay.

W R

GOOD
CONDITION

7.Thermo unit

●

Remove the thermo unit from the
crankcase.

●

Connect the pocket tester (

Ω

100) to the

thermo unit

●

Immerse the thermo unit in engine oil

●

Measure the resistance.

Thermo unit resistance:

150 °C (302 °F): 307 ~ 339

Ω

170 °C (338 °F): 209 ~ 231

Ω

WARNING

Handle the thermo unit with special care.
Never subject it to a strong shock or allow
it to be dropped. Should it be dropped, it
must be replaced.

Thermo unit:

20 Nm (2.0 m • kg, 14 ft • lb)

BAD CONDITION

Replace the thermo unit.

Summary of Contents for YFM400FAR


































































































































































































































































































































































































































































































Search results

Summary of Contents for YFM400FAR

Reviews:

Related manuals for YFM400FAR

Brands by name

Popular brands

Yamaha YFM400FAR, Service Manual

Search results

Summary of Contents for YFM400FAR

Reviews:

Related manuals for YFM400FAR

Brands by name

Popular brands