Yamaha YFM400FAR Service Manual Download Page 413

Page: 413 / 481

– 39 –

CHK

ADJ

CHECKING THE OIL TEMPERATURE WARNING LIGHT

ENGINE

CHECKING THE OIL TEMPERATURE
WARNING LIGHT

Oil temperature warning light

Turn the main switch to “ON” and the
engine stop switch to “

”.

Oil temperature warning
light does not come on.

Oil temperature warning
light comes on.

Check engine oil temperature.

Oil temperature warning
light does not come on.

Engine oil temperature and
electrical circuit are OK. Go
ahead with riding.

Push start switch with the
transmission in neutral.

Inspect the electrical circuit.
Refer to “SIGNAL SYSTEM”.

Oil tempera-
ture is low.

Allow to cool.

Oil tempera-
ture is high.

Oil temperature
warning light comes
on momentarily.

Oil temperature warning light checking method

Summary of Contents for YFM400FAR


































































































































































































































































































































































































































































































Search results

Summary of Contents for YFM400FAR

Reviews:

Brands by name

Popular brands

Yamaha YFM400FAR, Service Manual

Search results

Summary of Contents for YFM400FAR

Reviews:

Brands by name

Popular brands