manualshive.com logo in svg

Yamaha YFM400FAR, Service Manual

Share
Download
Yamaha YFM400FAR Service Manual Download Page 336

9 - 29

–

+

ELEC

LIGHTING SYSTEM

EB805021

2.If the taillight fails to come on:

CONTINUITY

1.Bulb and bulb socket

●

Check the bulb and bulb socket for
continuity.

NO CONTINUITY

Replace the bulb and/or bulb socket.

2.Voltage

●

Connect the pocket tester (20 V) to the bulb
socket coupler.

Tester (+) lead 

→

 Blue lead 

1

 

Tester (–) lead 

→

 Black lead 

2

 

L

Y

B

1

2

MEETS
SPECIFICATION

●

Turn the main switch to “ON”.

●

Turn the light switch to “

” or “

”.

●

Check the voltage (12 V) of the “Blue” lead
on the bulb socket connector.

This circuit is not faulty.

OUT OF SPECIFICATION

The wiring circuit from the main switch to the
bulb socket connector is faulty, repair it.

Summary of Contents for YFM400FAR


































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands