manualshive.com logo in svg

Yamaha YFM25RY, Owner'S Manual

Share
Download
Yamaha YFM25RY Owner'S Manual Download Page 93

 

8-21

 

1

2

3

4

5

6

7

8

9

10

11

 

chart.
The throttle cable free play should measure 2.0–
4.0 mm (0.08–0.16 in) at the throttle lever. Period-
ically check the throttle cable free play and, if nec-
essary, adjust it as follows.

TIP

 

The engine idling speed must be checked, and ad-
justed if necessary, before adjusting the throttle ca-

 

ble free play.

1. Loosen the locknut.
2. To increase the throttle cable free play, turn

the throttle cable free play adjusting bolt in di-
rection (a). To decrease the throttle cable free
play, turn the adjusting bolt in direction (b).

3. Tighten the locknut.

 

EBU24060

 

Valve clearance 

 

The valve clearance changes with use, resulting in
improper air-fuel mixture and/or engine noise. To
prevent this from occurring, the valve clearance
must be adjusted by a Yamaha dealer at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

 

1. Locknut

2.  Throttle cable free play adjusting bolt

3.  Throttle lever free play

3

2

1

(a)

(b)

Summary of Contents for YFM25RY



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands