manualshive.com logo in svg

Yamaha YFM25RY, Owner'S Manual

Share
Download
Yamaha YFM25RY Owner'S Manual Download Page 102

 

8-30

 

1

2

3

4

5

6

7

8

9

10

11

 

1. Loosen the locknut at the clutch lever.
2. To increase the clutch lever free play, turn the

adjusting bolt in direction (a), and to decrease
it, turn the bolt in direction (b).

3. Tighten the locknut.

TIP

 

If the specified free play cannot be obtained as de-
scribed above or if the clutch does not operate cor-
rectly, have a Yamaha dealer check the internal

 

clutch mechanism.

 

EBU26863

 

Drive chain slack 

 

The drive chain slack should be checked before
each ride and adjusted if necessary.

 

To check the drive chain slack

 

1. Place the ATV on a level surface.

TIP

 

When checking and adjusting the drive chain
slack, there should be no weight on the ATV and

 

all tires must be touching the ground.

2. Move the ATV back and forth to locate the

tightest portion of the drive chain, and then
measure the drive chain slack as shown.

 

1.  Clutch lever free play

2.  Clutch lever free play adjusting bolt

3. Locknut

1

2

(a)

(b)

3

 

Drive chain slack:

45.0–55.0 mm (1.77–2.17 in)

Summary of Contents for YFM25RY



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands