manualshive.com logo in svg

Yamaha YFM25RY, Owner'S Manual

The Yamaha YFM25RY Owner's Manual is available for free download on our website. This comprehensive manual provides detailed instructions, maintenance tips, and troubleshooting information to ensure you get the most out of your Yamaha YFM25RY. Visit our website today to download your copy and enhance your ATV experience.

Share
Download
background image

 

5-6

 

1

2

3

4

5

6

7

8

9

10

11

 

Set the tire pressure when the tires are cold. Set
the tire pressures to the following specifications:

 

EBU19830

 

Tire wear limit 

 

Replace the tire when the tire groove decreases to
3 mm (0.12 in).

 

1.  Low-pressure tire gauge

 

Recommended pressure:

Front

27.5 kPa (0.275 kgf/cm

 

2

 

, 4.0 psi)

Rear

27.5 kPa (0.275 kgf/cm

 

2

 

, 4.0 psi)

Minimum:

Front

24.5 kPa (0.245 kgf/cm

 

2

 

, 3.6 psi)

Rear

24.5 kPa (0.245 kgf/cm

 

2

 

, 3.6 psi)

 

1.  Tire wear limit

Summary of Contents for YFM25RY



































































































































Reviews:

No comments

Related manuals for YFM25RY

Brands by name

Popular brands

Load more brands