manualshive.com logo in svg

Yamaha YFM25RY, Owner'S Manual

The Yamaha YFM25RY Owner's Manual is available for free download on our website. This comprehensive manual provides detailed instructions, maintenance tips, and troubleshooting information to ensure you get the most out of your Yamaha YFM25RY. Visit our website today to download your copy and enhance your ATV experience.

Share
Download
background image

 

2-5

 

1

2

3

4

5

6

7

8

9

10

11

5

5LP-21696-M0

27.5 kPa

0.275 kgf/cm

2

4.0 psi

27.5 kPa

0.275 kgf/cm

2

4.0 psi

GB

D

E

F

I

NL

P

S

Set with tires cold.

Pneus à froid.

Bei kalten Reifen.

Ajuste con los
neumáticos an frío.

Impostare a pneumatici
freddi.

Ställ in med kalla däck.

Wanneer de banden
koud zijn.

Regular com pneus
frios.

For Europe

For Oceania

5

For Europe

7

6

WARNING

q

Improper tire pressure or overloading can cause 
loss of control.

Loss of control can result in severe injury or 
death.

OPERATING TIRE PRESSURE : 

Set with tires cold

LOADING

0

  Never set tire pressure below minimum.

It could cause the tire to dislodge from the rim.

0

  Maximum Vehicle Load : 100kg, (220lbs).

Includes weight of operator, cargo and accessories.

4D3-2816M-00

0

  Recommended  :  Front     : 27.5kPa, (4.0psi)

Rear    :  27.5kPa, (4.0psi)

0

  Minimum 

 :  Front     : 24.5kPa, (3.6psi)

Rear

: 24.5kPa, (3.6psi)

Summary of Contents for YFM25RY



































































































































Reviews:

No comments

Related manuals for YFM25RY

Brands by name

Popular brands

Load more brands