Yamaha YFM25RY Owner'S Manual Download | Manualshive

Page: 89 / 130

background image

8-17

1

2

3

4

5

6

7

8

9

10

11

13. Install the washer onto the air filter element

frame, and then insert the wing bolt into the
hole in the air filter element frame.

NOTICE

ECB00451

Be sure to install the washer with the bent edge

facing outward as shown.

14. Insert the air filter element into the air filter

case, and then tighten the wing bolt.

15. Install the air filter case cover by hooking the

holders onto the air filter case.

16. Install the seat.

TIP

The air filter element should be cleaned every 20–
40 hours. It should be cleaned and lubricated more
often if the ATV is operated in extremely dusty ar-
eas. Each time the air filter element maintenance
is performed, check the air inlet of the air filter case
for obstructions. Check the air filter case rubber
joint to the carburetor fittings and the rubber joint
manifold fittings for an air-tight seal. Tighten all fit-
tings securely to avoid the possibility of unfiltered

air entering the engine.

NOTICE

ECB00460

●

Make sure that the air filter element is prop-
erly seated in the air filter case.

●

Never operate the engine with the air filter el-
ement removed. This will allow unfiltered air
to enter the engine, causing rapid engine
wear and possible engine damage. Addition-
ally, operation without the air filter element
will affect carburetor jetting with subsequent
poor performance and possible engine over-

heating.

1. Washer

1

«
...
87
88
89
90
91
...
»

Summary of Contents for YFM25RY



































































































































Reviews:

No comments

Related manuals for YFM25RY

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands