Yamaha YFM25RY Owner'S Manual Download | Manualshive

Page: 101 / 130

background image

8-29

1

2

3

4

5

6

7

8

9

10

11

EBU24740

Brake light switches

The operation of the brake light switches must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.
The brake light switch for the brake pedal can be
adjusted as follows, but the other brake light
switches should be adjusted by a Yamaha dealer.

TIP

The brake light switch is properly adjusted when
the brake light comes on just before braking takes

effect.

Turn the adjusting nut while holding the brake light
switch in place. To make the brake light come on
earlier, turn the adjusting nut in direction (a). To
make the brake light come on later, turn the adjust-
ing nut in direction (b).

EBU24810

Adjusting the clutch lever free play

The clutch lever free play must be checked and, if
necessary, adjusted at the intervals specified in
the periodic maintenance and lubrication chart.
The clutch lever free play should measure 5.0–
10.0 mm (0.20–0.39 in) as shown. If the free play
is incorrect, adjust it as follows.

1. Brake light switch

2. Brake light switch adjusting nut

1

2

(b)

(a)

«
...
99
100
101
102
103
...
»

Summary of Contents for YFM25RY



































































































































Reviews:

No comments

Related manuals for YFM25RY

Brand: Baja motorsports Pages: 83

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands