Yamaha XVS1300CU Owner'S Manual Download Page 50

Page: 50 / 90

PERIODIC MAINTENANCE AND ADJUSTMENT

6-11

4. Remove the engine oil filler cap,

the engine oil drain bolt and its
gasket to drain the oil from the
crankcase.

TIP

Skip steps 5–7 if the oil filter cartridge
is not being replaced.

5. Remove the oil filter cartridge with

an oil filter wrench.

TIP

An oil filter wrench is available at a
Yamaha dealer.

6. Apply a thin coat of clean engine

oil to the O-ring of the new oil filter
cartridge.

TIP

Make sure that the O-ring is properly
seated.

7. Install the new oil filter cartridge

with an oil filter wrench, and then
tighten it to the specified torque
with a torque wrench.

1. Engine oil drain bolt
2. Gasket

1. Oil filter cartridge
2. Oil filter wrench

1. O-ring

U2SSE0E0.book Page 11 Monday, November 18, 2013 3:20 PM

Summary of Contents for XVS1300CU



























































































Search results

Summary of Contents for XVS1300CU

Reviews:

Related manuals for XVS1300CU

Brands by name

Popular brands

Yamaha XVS1300CU, Owner'S Manual

Search results

Summary of Contents for XVS1300CU

Reviews:

Related manuals for XVS1300CU

Brands by name

Popular brands