Yamaha XVS1300CU Owner'S Manual Download Page 22

Page: 22 / 90

INSTRUMENT AND CONTROL FUNCTIONS

3-7

3. Turn the key to “ON”, and then re-

lease the “SELECT” switch after
five seconds.

4. Adjust the multi-function meter

unit panel brightness level by
pushing the “SELECT” switch.

5. Push the “RESET” switch.

The display will change to the prior
mode.

EAU1234G

Han

ar switches

Left

EAU12351

Pass switch “

”

Press this switch to flash the headlight.

EAU12401

Dimmer switch “

”

Set this switch to “

” for the high

beam and to “

” for the low beam.

EAU12461

Turn si

nal switch “

”

To signal a right-hand turn, push this
switch to “

”. To signal a left-hand

turn, push this switch to “

”. When

released, the switch returns to the cen-

1. Pass switch “

”

2. Dimmer switch “

”

3. Turn signal switch “

”

4. Horn switch “

”

3
4

1. Engine stop switch “

”

2. “SELECT” switch
3. “RESET” switch
4. Start switch “

”

5. Hazard switch “

”

2
3
4

U2SSE0E0.book Page 7 Monday, November 18, 2013 3:20 PM

Summary of Contents for XVS1300CU



























































































Search results

Summary of Contents for XVS1300CU

Reviews:

Related manuals for XVS1300CU

Brands by name

Popular brands

Yamaha XVS1300CU, Owner'S Manual

Search results

Summary of Contents for XVS1300CU

Reviews:

Related manuals for XVS1300CU

Brands by name

Popular brands