Yamaha XVS1300CU Owner'S Manual Download Page 19

Page: 19 / 90

INSTRUMENT AND CONTROL FUNCTIONS

3-4

EAU50693

Multi-function meter unit

WARNING

EWA12423

Be sure to stop the vehicle

efore

makin

any settin

chan

es to the

multi-function meter unit. Chan

settin

s while ri

can

istract the

operator an

increase the risk of an

acci

ent.

The multi-function meter unit is
equipped with the following:



a speedometer



an odometer



two tripmeters (which show the
distance traveled since they were
last set to zero)



a fuel reserve tripmeter (which
shows the distance traveled on
the fuel reserve)



a fuel meter



a clock



a self-diagnosis device



a brightness control mode

TIP

Be sure to turn the key to “ON” before
using the “SELECT” and “RESET”
switches, except for setting the bright-
ness control mode.

Spee

ometer

When the key is turned to “ON”, the
speedometer needle will sweep once
across the speed range and then re-
turn to zero in order to test the electri-
cal circuit.

1. Speedometer
2. Odometer/tripmeter/fuel reserve tripme-

ter/fuel meter/clock

1. “SELECT” switch
2. “RESET” switch

1
2

1. Speedometer

U2SSE0E0.book Page 4 Monday, November 18, 2013 3:20 PM

Summary of Contents for XVS1300CU



























































































Search results

Summary of Contents for XVS1300CU

Reviews:

Related manuals for XVS1300CU

Brands by name

Popular brands

Yamaha XVS1300CU, Owner'S Manual

Search results

Summary of Contents for XVS1300CU

Reviews:

Related manuals for XVS1300CU

Brands by name

Popular brands