Yamaha XVS1300CU Owner'S Manual Download Page 68

Page: 68 / 90

PERIODIC MAINTENANCE AND ADJUSTMENT

6-29

turne

to “OFF”, then

iscon-

nect the ne

ative lea

efore

isconnectin

the positive lea

[ECA16303]

2. If the battery will be stored for

more than two months, check it at
least once a month and fully
charge it if necessary.

3. Fully charge the battery before in-

stallation.

NOTICE:

When install-

the

attery,

e sure the key

is turne

to “OFF”, then connect

the positive lea

efore con-

nectin

the ne

ative lea

[ECA16841]

4. After installation, make sure that

the battery leads are properly con-
nected to the battery terminals.

NOTICE

ECA16531

Always keep the

attery char

Storin

ischar

attery can

cause permanent

attery

ama

EAU50811

Replacin

the fuses

The main fuse, the fuel injection sys-
tem fuse, and the fuse box, which con-
tains the fuses for the individual
circuits, are located under the seat.
(See page 3-13.)

TIP

To access the fuel injection system
fuse, remove the starter relay cover by
pulling it upward.

1. Fuel injection system spare fuse
2. Fuel injection system fuse
3. Fuse box
4. Main fuse

1. Signaling system fuse
2. Ignition fuse
3. Parking lighting fuse
4. Radiator fan fuse
5. Backup fuse (for clock)
6. Headlight fuse
7. Spare fuse

U2SSE0E0.book Page 29 Monday, November 18, 2013 3:20 PM

Summary of Contents for XVS1300CU



























































































Search results

Summary of Contents for XVS1300CU

Reviews:

Related manuals for XVS1300CU

Brands by name

Popular brands

Yamaha XVS1300CU, Owner'S Manual

Search results

Summary of Contents for XVS1300CU

Reviews:

Related manuals for XVS1300CU

Brands by name

Popular brands