Yamaha XVS1300CU Owner'S Manual Download Page 48

Page: 48 / 90

PERIODIC MAINTENANCE AND ADJUSTMENT

6-9

3. Remove the spark plug as shown,

with the spark plug wrench includ-
ed in the additional tool kit, which
was handed out separately at the
purchase of the vehicle.

To check the spark plu

1. Check that the porcelain insulator

around the center electrode on
each spark plug is a medium-to-
light tan (the ideal color when the
vehicle is ridden normally).

2. Check that all spark plugs in-

stalled in the engine have the
same color.

TIP

If any spark plug shows a distinctly dif-
ferent color, the engine could be oper-
ating improperly. Do not attempt to
diagnose such problems yourself. In-
stead, have a Yamaha dealer check
the vehicle.

3. Check each spark plug for elec-

trode erosion and excessive car-
bon or other deposits, and replace
it if necessary.

4. Measure the spark plug gap with a

wire thickness gauge and, if nec-
essary, adjust the gap to specifi-
cation.

To install a spark plu

1. Clean the surface of the spark

plug gasket and its mating sur-
face, and then wipe off any grime
from the spark plug threads.

2. Install the spark plug with the

spark plug wrench, and then tight-
en it to the specified torque.

1. Spark plug cap

1. Spark plug wrench

Specifie

spark plu

NGK/LMAR7A-9

1. Spark plug gap

Spark plu

ap:

0.8–0.9 mm (0.031–0.035 in)

htenin

torque:

Spark plug:

13 Nm (1.3 m·kgf, 9.4 ft·lbf)

U2SSE0E0.book Page 9 Monday, November 18, 2013 3:20 PM

Summary of Contents for XVS1300CU



























































































Search results

Summary of Contents for XVS1300CU

Reviews:

Related manuals for XVS1300CU

Brands by name

Popular brands

Yamaha XVS1300CU, Owner'S Manual

Search results

Summary of Contents for XVS1300CU

Reviews:

Related manuals for XVS1300CU

Brands by name

Popular brands