Yamaha WaveRunner VX 2018 Page 65 Owner'S/Operator'S Manual Download

Page: 65 / 108

Pre-operation checks

TIP:

To ensure safety and reliability, pre-operation checks should be made each time the water-
craft is used.

Stern drain plugs

Check the stern drain plugs for damage and foreign
material and check that they are securely installed.

Hood

Check that the hood is securely closed.

Front and rear seats

Check that the seats are securely installed.

POST-LAUNCH CHECKS

Cooling water pilot outlet

Check that water is discharged from the cooling
water pilot outlet while the engine is running.

Multifunction information
center

Check the multifunction information center for prop-
er operation.

Shift system

Check the shift system for proper operation.

Engine idling speed

Check the engine idling speed.

ITEM

ROUTINE

PAGE

UF4G72E0.book Page 59 Tuesday, August 1, 2017 11:30 AM

Summary of Contents for WaveRunner VX 2018













































































































Search results

Summary of Contents for WaveRunner VX 2018

Reviews:

Related manuals for WaveRunner VX 2018

Brands by name

Popular brands

Yamaha WaveRunner VX 2018, Owner'S/Operator'S Manual

Search results

Summary of Contents for WaveRunner VX 2018

Reviews:

Related manuals for WaveRunner VX 2018

Brands by name

Popular brands