Yamaha WaveRunner VX 2018 Page 85 Owner'S/Operator'S Manual Download | Manualshive

Page: 85 / 108

background image

Operation

79

EJU40242

After removing the watercraft from
the water

NOTICE

ECJ01311

Do not run the engine over 4000 r/min on
land. Also, do not run the engine for more
than 15 seconds without supplying water,
otherwise the engine could overheat.

After operating and removing the watercraft
from the water, promptly discharge the re-
maining water from the cooling water pas-
sages.
To discharge water from the cooling water
passages:
(1) Make sure that the area around the wa-

tercraft is clear, and then start the en-
gine.

(2) Discharge the remaining water out of the

cooling water passages by alternately
squeezing and releasing the throttle lever
quickly for 10 to 15 seconds.

(3) Stop the engine.

UF4G72E0.book Page 79 Tuesday, August 1, 2017 11:30 AM

«
...
83
84
85
86
87
...
»

Summary of Contents for WaveRunner VX 2018













































































































Reviews:

No comments

Related manuals for WaveRunner VX 2018

Brand: C&L Marine Pages: 14

Brand: Yamarin Cross Pages: 121

Brand: Corsiva Yachting Pages: 31

Brand: Four winns Pages: 134

Brand: Four winns Pages: 140

Brand: Laser Performance Pages: 18

Brand: LaserPerformance Pages: 7

Brand: LaserPerformance Pages: 17

2002 Response Series

Brand: Malibu Boats Pages: 76

Brand: Hunter Pages: 145

Brand: Baja Pages: 82

Brand: BENETEAU Pages: 104

Brand: AKONA Pages: 12

SUN ODYSSEY 42 DS

Brand: Jeanneau Pages: 30

GP1300R WaveRunner 2003

Brand: Yamaha Pages: 279

Brand: Paddle King Pages: 11

Cayman II Kayak

Brand: Maxxon Pages: 6

DC 235 DUAL CONSOLE

Brand: PERSUIT Pages: 120

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands