Yamaha WaveRunner VX 2018 Owner'S/Operator'S Manual Download | Manualshive

Page: 34 / 108

background image

Control function operation

28

will not start. Also, the starter motor could
be damaged.

[ECJ01041]

The engine will not start under any of the fol-
lowing conditions:



Clip is removed from the engine shut-off
switch.



Throttle lever is squeezed.



Throttle lever is malfunctioning.



RiDE lever is squeezed.



RiDE lever is malfunctioning.



VX Deluxe / VX Cruiser / VX Limited: Lock
mode of the Yamaha Security System has
been selected. (See page 26 for Yamaha
Security System setting procedures.)

EJU31212

Throttle lever

The throttle lever increases the engine speed
when the lever is squeezed.

The throttle lever returns automatically to its
fully closed (idle) position when released.

EJU43342

RiDE lever

When the RiDE lever is squeezed, the reverse
gate lowers and the watercraft starts moving
in reverse. If the watercraft is moving forward,
the watercraft gradually slows down until it
stops, and then the watercraft starts moving
in reverse.

When the RiDE lever is released, it automati-
cally returns to its fully closed (idle) position
and the reverse gate moves to the neutral po-
sition.

EJU31262

Steering system

By turning the handlebars in the direction you
wish to travel, the angle of the jet thrust noz-

1

Start switch

1

Throttle lever

1

1

1

RiDE lever

1

UF4G72E0.book Page 28 Tuesday, August 1, 2017 11:30 AM

«
...
32
33
34
35
36
...
»

Summary of Contents for WaveRunner VX 2018













































































































Reviews:

No comments

Related manuals for WaveRunner VX 2018

Brand: Sailfish Pages: 44

Brand: Malibukayaks Pages: 23

Sun Odyssey 490

Brand: Jeanneau Pages: 61

Brand: Sea Pro Pages: 50

Brand: Highfield Pages: 34

Brand: grabner Pages: 12

Brand: J&J Amusements Pages: 171

Brand: Sea-doo Pages: 130

Brand: Jensen Pages: 15

Brand: White Formula Pages: 23

Brand: Prestige Pages: 116

Brand: Tiara Yachts Pages: 152

Brand: HonWave Pages: 38

Performance 275

Brand: Baja Pages: 87

Sportfish Tournament Edition 230

Brand: Baja Pages: 83

Brand: M.E.S. Marine Pages: 27

Brand: Sea-doo Pages: 105

Brand: NW Explorations Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands