Yamaha WaveRunner VX 2018 Owner'S/Operator'S Manual Download

Page: 91 / 108

Care and storage

the air filter case cover could be dam-
aged.

[ECJ02620]

(3) Spray a rust inhibitor into the intake

opening for 3 seconds.

WARNING! Do

not spray flammable rust inhibitor
products on engine surfaces while the
engine is hot. The sprayed substance
or propellants could catch fire.

[EWJ00262]

(4) Place the air filter case cover in its origi-

nal position, and then fit the hooks onto
the cover.

TIP:

Make sure that the air filter case cover is se-
curely installed.
(5) Make sure that the area around the wa-

tercraft is clear, and then start the engine
in a well-ventilated area and let it run at

idle for 15 seconds. (See page 27 for in-
formation on starting the engine.)

(6) Stop the engine.
(7) Securely install the seats in their original

positions.

Hook

Air filter case cover

Intake opening

UF4G72E0.book Page 85 Tuesday, August 1, 2017 11:30 AM

Summary of Contents for WaveRunner VX 2018













































































































Search results

Summary of Contents for WaveRunner VX 2018

Reviews:

Related manuals for WaveRunner VX 2018

Brands by name

Popular brands

Yamaha WaveRunner VX 2018, Owner'S/Operator'S Manual

Search results

Summary of Contents for WaveRunner VX 2018

Reviews:

Related manuals for WaveRunner VX 2018

Brands by name

Popular brands