Yamaha WaveRunner VX 2018 Page 5 Owner'S/Operator'S Manual Download

Page: 5 / 108

Table of contents

General and important labels........... 1

Identification numbers .................... 1

number............................................ 1

Craft Identification Number (CIN) .......  1
Engine serial number..........................  1
Manufactured date label ....................  2

Model information ........................... 2

Builder’s plate .................................... 2

Important labels .............................. 4

Warning labels.................................... 5
Other labels ........................................ 8

Safety information........................... 10

Limitations on who may operate

the watercraft ............................. 10

Cruising limitations........................  11
Operation requirements ................  12
Recommended equipment ...........  14
Hazard information........................  15
Watercraft characteristics .............  15
Wakeboarding and water-skiing ...  17
Safe boating rules .........................  18
Enjoy your watercraft

responsibly................................. 19

Description....................................... 20

Watercraft glossary ....................... 20
Location of main components ...... 21

Control function operation ............. 25

Watercraft control functions ......... 25

Remote control transmitter

(VX Deluxe / VX Cruiser /
VX Limited).................................... 25

Yamaha Security System

(VX Deluxe / VX Cruiser /
VX Limited).................................... 26

Engine stop switch ..........................  27
Engine shut-off switch ....................  27
Start switch .....................................  27
Throttle lever ....................................  28
RiDE lever ........................................  28

Steering system................................  28
Cooling water pilot outlet .................  29
Water separator................................  29

Watercraft operation ...................... 31

Watercraft operation functions ..... 31

Shift system ..................................... 31

Watercraft operation modes ......... 33

Low RPM Mode (VX Deluxe /

VX Cruiser / VX Limited)................ 33

No-wake mode (VX Deluxe /

VX Cruiser / VX Limited)................ 34

Cruise assist (VX Deluxe /

VX Cruiser / VX Limited)................ 36

Instrument operation ...................... 38

Multifunction information center... 38

Information display...........................  38
Hour meter .......................................  41
Voltmeter ..........................................  41

Equipment operation ...................... 43

Equipment..................................... 43

Seats ................................................  43
Handgrip...........................................  44
Reboarding step...............................  44
Bow eye............................................  45
Stern eyes ........................................  45
Cleat .................................................  45
Pull-up cleats (VX Limited) ...............  46
Storage compartments ....................  46
Fire extinguisher holder and cover ...  48

Operation and handling
requirements ................................... 50

Fuel requirements ......................... 50

Fuel................................................... 50

Engine oil requirements ................ 53

Engine oil.......................................... 53

Draining the bilge water ................ 54

Draining the bilge water on land....... 54
Draining the bilge water on water .... 55

UF4G72E0.book Page 1 Tuesday, August 1, 2017 11:30 AM

Summary of Contents for WaveRunner VX 2018













































































































Search results

Summary of Contents for WaveRunner VX 2018

Reviews:

Related manuals for WaveRunner VX 2018

Brands by name

Popular brands

Yamaha WaveRunner VX 2018, Owner'S/Operator'S Manual

Search results

Summary of Contents for WaveRunner VX 2018

Reviews:

Related manuals for WaveRunner VX 2018

Brands by name

Popular brands