Yamaha WaveRunner VX 2018 Owner'S/Operator'S Manual Download

Page: 49 / 108

Equipment operation

EJU40334

Equipment

EJU42203

Seats

The front and rear seats are removable.
Remove the seats to access the engine com-
partment and removable watertight storage
compartment.
To remove the rear seat:
(1) Pull the rear seat latch up, and then lift up

the rear of the seat.

(2) Pull the seat rearward and remove it.

To install the rear seat:
(1) Insert the projections on the front of the

seat into the stays on the deck.

(2) Push the rear of the seat down to secure-

ly lock it in place.

To remove the front seat:
(1) Remove the rear seat.
(2) Pull the front seat latch up, and then lift

up the rear of the seat.

Seat latch

UF4G72E0.book Page 43 Tuesday, August 1, 2017 11:30 AM

Summary of Contents for WaveRunner VX 2018













































































































Search results

Summary of Contents for WaveRunner VX 2018

Reviews:

Related manuals for WaveRunner VX 2018

Brands by name

Popular brands

Yamaha WaveRunner VX 2018, Owner'S/Operator'S Manual

Search results

Summary of Contents for WaveRunner VX 2018

Reviews:

Related manuals for WaveRunner VX 2018

Brands by name

Popular brands