Yamaha VX200D Owner'S Manual Download

Page: 42 / 81

Operation

Push the power tilt / power trim and tilt
switch “

” (down) to lower the outboard

motor to the desired position.

EMU28060

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

EMU28090

Power trim and tilt models / power tilt
models

The outboard motor can be tilted up partially

to allow operation in shallow water.

WARNING

EWM00660

●

Place the gear shift in neutral before
setting up for shallow water cruising.

●

Return the outboard motor to its normal
position as soon as the boat is back in

deeper water.

CAUTION:

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

ing can result.

EMU28184

Procedure for power trim and tilt / power
tilt models

Place the gear shift lever in neutral.

Slightly tilt the outboard motor up to the
desired position using the power trim / tilt
switch.

ZMU01936

ZMU04147

✩✩✬✤✫✲✣ ✦✪

Summary of Contents for VX200D


















































































Search results

Summary of Contents for VX200D

Reviews:

Related manuals for VX200D

Brands by name

Popular brands

Yamaha VX200D, Owner'S Manual

Search results

Summary of Contents for VX200D

Reviews:

Related manuals for VX200D

Brands by name

Popular brands