background image

 

 

http://www.TYAN.com 

 

 

 

 

Thunder K7X Pro 

/// 

S2469 

Revision 1.50

 

 

 

Copyright © TYAN Computer Corporation, 2001-2002. All rights reserved. No part of this manual 
may be reproduced or translated without prior written consent from TYAN Computer Corp. 
 
 
All registered and unregistered trademarks and company names contained in this manual are 
property of their respective owners including, but not limited to the following. 
 
TYAN, Thunder K7X Pro S2469 are trademarks of TYAN Computer Corporation. 
AMD, Athlon, and combinations thereof are trademarks of AMD Corporation. 
Phoenix, PhoenixBIOS are trademarks of Phoenix Software Inc. 
Microsoft, Windows are trademarks of Microsoft Corporation. 
IBM, PC, AT, PS/2 are trademarks of IBM Corporation. 
Winbond is a trademark of Winbond Electronics Corporation. 
 
 
 
 
Information contained in this document is furnished by TYAN Computer Corporation and has been 
reviewed for accuracy and reliability prior to printing. TYAN assumes no liability whatsoever, and 
disclaims any express or implied warranty, relating to sale and/or use of TYAN products including 
liability or warranties relating to fitness for a particular purpose or merchantability. TYAN retains the 
right to make changes to product descriptions and/or specifications at any time, without notice. In 
no event will TYAN be held liable for any direct or indirect, incidental or consequential damage, 
loss of use, loss of data or other malady resulting from errors or inaccuracies of information 
contained in this document. 

 
 
 
 
 
 

Summary of Contents for S2469






































Reviews: