Yamaha VX200D Owner'S Manual Download

Page: 22 / 81

Basic components

EMU26470

Tachometer

This gauge shows the engine speed and has
the following functions.

EMU26491

Digital tachometer

The tachometer shows the engine speed
and has the following functions.

NOTE:

All segments of the display will light momen-
tarily after the main switch is turned on and

will return to normal thereafter.

NOTE:

The water separator and engine trouble
warning indicators only operate when the en-
gine is equipped with the appropriate func-

tions.

EMU26540

Oil level indicators (three indicators
2)

The indicators on the gauge show the status
of the oil level. For details on how to read the
indicators, see page 29.

CAUTION:

ECM00030

Do not operate the engine without oil. Se-

rious engine damage will occur.

1. Flushing device

1. Tachometer
2. Oil level indicator

ZMU04139

ZMU04577

1. Tachometer
2. Trim meter
3. Hour meter
4. Oil level indicator
5. Overheat warning indicator
6. Water separator warning indicator
7. Engine trouble warning indicator
8. Set button
9. Mode button

ZMU01958

✩✩✬✤✫✲✣ ✤✪

Summary of Contents for VX200D


















































































Search results

Summary of Contents for VX200D

Reviews:

Related manuals for VX200D

Brands by name

Popular brands

Yamaha VX200D, Owner'S Manual

Search results

Summary of Contents for VX200D

Reviews:

Related manuals for VX200D

Brands by name

Popular brands