background image

 

Maintenance

 

44

 

more likely to corrode. If necessary, clean
and paint the areas. A touch-up paint is avail-
able from your Yamaha dealer.

 

EMU28485

 

Periodic maintenance

WARNING

 

EWM01070 

 

Be sure to turn off the engine when you
perform maintenance unless otherwise
specified. If you or the owner is not famil-
iar with machine servicing, this work
should be done by your Yamaha dealer or

 

other qualified mechanic.

Maintenance, replacement, or repair of
the emission control devices and sys-
tems may be performed by any marine
engine repair establishment or individual.
All warranty repairs, however, including
those to the emission control system,
must be performed by an authorized
Yamaha marine dealership.

 

A service manual is available for purchase
through your Yamaha dealer for owners who
have the mechanical skills, tools, and other
equipment necessary to perform mainte-
nance not covered by this owner’s manual.

 

EMU28510

 

Replacement parts

 

If replacement parts are necessary, use only
genuine Yamaha parts or parts of the same
type and of equivalent strength and materi-
als. Any part of inferior quality may malfunc-
tion, and the resulting loss of control could
endanger the operator and passengers.
Yamaha genuine parts and accessories are
available from your Yamaha dealer.

✩✩✬✤✫✲✣ ✧✧   

Summary of Contents for VX200D


















































































Reviews: