Yamaha VX200D Page 23 Owner'S Manual Download | Manualshive

Page: 23 / 81

background image

Basic components

18

EMU26550

Oil level indicator (digital type)

This indicator shows the engine oil level. If
the oil level falls below the lower limit, the
warning indicator will start to blink. For fur-
ther information, see page 22.

CAUTION:

ECM00030

Do not operate the engine without oil. Se-

rious engine damage will occur.

EMU26581

Overheat warning indicator (digital
type)

If the engine temperature rises too high, the
warning indicator will start to blink. For fur-
ther information on reading the indicator, see

page 21.

CAUTION:

ECM00050

Do not continue to run the engine if the
overheat warning indicator is on. Serious

engine damage will occur.

EMU26600

Speedometer (digital type)

This gauge shows the boat speed.

NOTE:

After the main switch is first turned on, all
segments of the display come on as a test.
After a few seconds, the gauge will change
to normal operation. Watch the gauge when

1. Oil level indicators

1. Oil level indicator

ZMU04580

1

1

ZMU01867

1. Overheat warning indicator

1. Speedometer
2. Fuel gauge
3. Trip meter/clock/voltmeter
4. Warning indicator(s)

1

ZMU01868

✩✩✬✤✫✲✣ ✤✫

«
...
21
22
23
24
25
...
»

Summary of Contents for VX200D


















































































Reviews:

No comments

Related manuals for VX200D

Brand: JETWAY Pages: 44

Brand: Biostar Pages: 27

Brand: Gigabyte Pages: 116

STEVAL-IME008V1

Brand: STMicroelectronics Pages: 19

Brand: JETWAY Pages: 48

Brand: NXP Semiconductors Pages: 35

JW-A880GMT-EXTREME

Brand: J&W Pages: 39

P35D3 Platinum - Motherboard - ATX

Brand: MSI Pages: 104

Brand: Gigabyte Pages: 19

Brand: Freescale Semiconductor Pages: 17

Brand: JETWAY Pages: 50

Brand: Linear Technology Pages: 8

Brand: Supero Pages: 105

bq51010BEVM-764

Brand: Texas Instruments Pages: 26

Brand: Motorola Pages: 57

PATX3070 Series

Brand: Motorola Pages: 83

Minimal PowerPC 603e

Brand: Motorola Pages: 16

Brand: Motorola Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands