Yamaha VX200D Page 24 Owner'S Manual Download | Manualshive

Page: 24 / 81

background image

Basic components

19

turning on the main switch to make sure all

segments come on.

NOTE:

The speedometer displays km/h, mph, or
knots, according to operator preference. Se-
lect the desired unit of measurement by set-
ting the selector switch on the back of the

gauge. See the illustration for settings.

EMU26610

Trim meter

This gauge shows the trim angle of your out-
board motor.

NOTE:

Memorize the trim angles that work best for
your boat under different conditions. Adjust
the trim angle to the desired setting with the

power trim and tilt switch.

EMU26620

Trim meter (digital type)

This meter shows the trim angle of your out-
board motor.

NOTE:

●

Memorize the trim angles that work best
for your boat under different conditions.
Adjust the trim angle to the desired using
the power trim and tilt switch.

●

If the trim angle of your motor exceeds the
trim operating range, the top segment on

the trim meter display will blink.

EMU26650

Hour meter (digital type)

This meter shows the number of hours the
engine has been run. It can be set to show
the total number of hours or the number of
hours for the current trip. The display can
also be turned on and off.

1. Cap
2. Selector switch (for speed unit)
3. Selector switch (for fuel sensor)

ZMU04581

ZMU01869

ZMU01870

✩✩✬✤✫✲✣ ✤✬

«
...
22
23
24
25
26
...
»

Summary of Contents for VX200D


















































































Reviews:

No comments

Related manuals for VX200D

Brand: Intel Pages: 89

Brand: TYAN Pages: 67

Brand: Arbor Technology Pages: 86

Brand: Unicorn Computer Pages: 36

Brand: JETWAY Pages: 52

Brand: Renesas Pages: 17

Brand: Digilent Pages: 17

Brand: Texas Instruments Pages: 51

Brand: Texas Instruments Pages: 20

Brand: IDT Pages: 39

Brand: ASROCK Pages: 65

Brand: Icop Pages: 30

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 124

Brand: Yamaha Pages: 122

Brand: Yamaha Pages: 125

Brand: Yamaha Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands