manualshive.com logo in svg

Yamaha VMAX VMX12P, Owner'S Manual

Share
Download
Yamaha VMAX VMX12P Owner'S Manual Download Page 92

PERIODIC MAINTENANCE AND MINOR REPAIR

6-41

6

EAU04187

Replacing the headlight bulb 

This motorcycle is equipped with a
quartz bulb headlight. If the headlight
bulb burns out, replace it as follows.

1. Remove the headlight unit by re-

moving the screws.

2. Disconnect the headlight coupler,

and then remove the bulb cover.

3. Remove the headlight bulb holder

by turning it counterclockwise, and
then remove the defective bulb.

EW000119

WARNING

_ 

Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down. 

_

4. Place a new headlight bulb into

position, and then secure it with
the bulb holder.

EC000105

CAUTION:

_ 

Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the bulb,
and the bulb life will be adversely af-
fected. Thoroughly clean off any dirt
and fingerprints on the headlight
bulb using a cloth moistened with
alcohol or thinner. 

_

5. Install the headlight bulb cover,

and then connect the coupler.

6. Install the headlight unit by install-

ing the screws.

7. Have a Yamaha dealer adjust the

headlight beam if necessary.

1. Screw (

×

 2)

1. Headlight bulb holder

1. Do not touch this area.

u5gk12.book  Page 41  Wednesday, June 13, 2001  8:55 AM

Summary of Contents for VMAX VMX12P






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands