manualshive.com logo in svg

Yamaha VMAX VMX12P, Owner'S Manual

Share
Download
Yamaha VMAX VMX12P Owner'S Manual Download Page 34

INSTRUMENT AND CONTROL FUNCTIONS

3-13

3

Spring preload

To increase the spring preload and
thereby harden the suspension, turn
the adjusting ring on each shock ab-
sorber assembly in direction 

a

. To de-

crease the spring preload and thereby
soften the suspension, turn the adjust-
ing ring on each shock absorber as-
sembly in direction 

b

.

NOTE:

@ 

●

Align the bottom edge of the ad-
justing ring with the appropriate
setting on the shock absorber. 

●

Use the special wrench included in
the owner’s tool kit to make this
adjustment. 

@

Damping force

To increase the damping force and
thereby harden the damping, turn the
adjusting knob on each shock absorber
assembly in direction 

a

. To decrease

the damping force and thereby soften
the damping, turn the adjusting knob
on each shock absorber assembly in
direction 

b

.

NOTE:

@ 

Align the appropriate setting on the ad-
justing knob with the position indicator
on the shock absorber.

Spring preload:

Minimum (soft): 1
Standard: 1
Maximum (hard): 5

1. Damping force adjusting knob
2. Position indicator

u5gk12.book  Page 13  Wednesday, June 13, 2001  8:55 AM

Summary of Contents for VMAX VMX12P






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands