manualshive.com logo in svg

Yamaha VMAX VMX12P, Owner'S Manual

Share
Download
Yamaha VMAX VMX12P Owner'S Manual Download Page 33

INSTRUMENT AND CONTROL FUNCTIONS

3-12

3

EC000012

CAUTION:

@ 

Never exceed the maximum air pres-
sure, otherwise the front fork oil
seals may become damaged. 

@

EWA00037

WARNING

@ 

There must be no difference in air
pressure between the left and right
fork legs, otherwise poor handling
and loss of stability may result. 

@

5. Securely install the air valve caps.

EAU01657

Adjusting the shock absorber 
assemblies 

Both shock absorber assemblies are
equipped with a spring preload adjust-
ing ring and a damping force adjusting
knob.

EC000015

CAUTION:

@ 

Never attempt to turn an adjusting
mechanism beyond the maximum
or minimum settings. 

@

EW000040

WARNING

@ 

Always adjust both shock absorber
assemblies equally, otherwise poor
handling and loss of stability may
result. 

@

Spring rate:

Minimum/standard (soft):

Air pressure = 

40 kPa (0.4 kgf/cm

2

, 5.7 psi)

Maximum (hard):

Air pressure = 

100 kPa (1.0 kgf/cm

2

, 14 psi)

1. Shock absorber assembly (

×

 2)

u5gk12.book  Page 12  Wednesday, June 13, 2001  8:55 AM

Summary of Contents for VMAX VMX12P






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands